![]() For the VP2410, the ports are numbered, not specifically “WAN” and “LAN”, so port reversal is not needed, but the configuration steps are shown below. In order to correct this issue see the PORT REVERSAL section below. Important Note: The ports marked “WAN” and “LAN” are reversed when using OPNsense. Once the OPNsense installation image is properly copied to the USB drive, it is ready to be installed on the Vault. Install the Operating System on the Vault If the unit is a VP2410 and has coreboot installed, it will be in UEFI mode by default. We have a Knowledge Base article which gives step by step instructions linked he r e. By changing the BIOS mode to UEFI the issue is resolved. Verify the BIOS ModeĪs mentioned above there is a simple fix to the bug introduced in 11.2. The 2 USB ports on the Vault are very close to each other and if either the USB stick or the USB keyboard plug is too wide, you will not be able to plug both in at the same time, which will prevent you from doing the installation. Note: If using the Vault FW1x, FW2x, or FW4x, be sure to use a USB stick and the USB keyboard with a plug that is relatively skinny. See this link for detailed instructions on how to create a bootable USB drive using Rufus or balenaEtcher. The easiest way to transfer the installation image to a USB drive is by using software called “ Rufus” on Windows or “ balenaEtcher” on Apple OSX. Burn the Installation Image to a USB Drive The resulting file should look the same, except that the file name will now end in “.img” instead of “.img.gz”. Now that the compressed image file has been downloaded, you will need to use a program like “ 7zip” or “ winzip” on Windows to decompress the file. Unless advised to the contrary, we recommend downloading the latest available version. This article shows an example installation with version 19.1 of OPNsense. A VGA installation will require a USB keyboard and HDMI monitor (FW2B, FW4B, FW6, VP) or VGA monitor (FW1, FW2, FW4A). If your computer does not have a DB9 serial connection, you will need a USB to serial adapter. In order to use the serial connection, you will need to use the blue RJ45 to serial cable provided with your vault. A Serial console installation allows you to interface with the OPNsense console without a physical keyboard or monitor. This is NOT how you will manage your OPNsense installation on a daily basis, but rather the way that you will access OPNsense in the event that you cannot log into the web UI. What you choose here depends on how you want to access the OPNsense console. The proper selections are as follows and shown in the screenshot below.Īrchitecture: AMD64 (64 bit) Note: The 32 bit version will not work. It is important to choose the correct options when downloading the image including “Architecture” and “Image Type”. The same image can be used to install OPNsense on any of the Vault platforms. The OPNsense installation image can be downloaded from. Obtain the Installation Image and Uncompress it If using UEFI only mode the USB installer will not appear in the boot menu. Note: The serial image uses the MBR partition scheme, which requires legacy BIOS. See the BIOS Compatibility table at the bottom of this article for more information. This article supersedes that one and following the instructions below eliminates the need to refer to the previous article. Both of these issues can be resolved by setting BIOS to UEFI mode on the Vault. Note: A previous article was published at this link regarding an important issue and workaround in OPNsense due to the fact that it is based on FreeBSD 11.2. LAN default IP address is 192.168.1.1 with DHCP enabled ![]() The VP2410 uses the OPNsense defaults and LAN is assigned to “1” and WAN is assigned to “2”. The VP2410 has numbered ports, not specifically labelled “WAN” and “LAN”. WAN and LAN are assigned to correctly match the ports as labeled on the Vault. By default, OPNsense assigns the LAN port to the first Ethernet port and the WAN port to the second Ethernet port. OPNsense can now be selected as a pre-installed option during checkout. More information about OPNsense can be found on the OPNsense website / It is a popular choice for those interested in an open source firewall. ![]() OPNsense is an open source, easy-to-use and easy-to-build HardenedBSD based firewall and routing platform.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |